Fluke-biomedical ESA620 User Manual Page 1

FBC-0028 January 2008, Rev. 2, 3/13 © 2008, 2013 Fluke Corporation. All rights reserved. Specifications are subject to change without notice. All pro

ESA620 Users Manual iv

v List of Tables Table Title Page 1. Symbols ...

ESA620 Users Manual vi

vii List of Figures Figure Title Page 1. Top-Panel Controls and Connections ...

ESA620 Users Manual viii 16. Mains to Non-Earth Accessible Conductive Points Schematic ... 27 17. Appli

1 Electrical Safety Analyzer Introduction The Fluke Biomedical ESA620 Electrical Safety Analyzer (hereafter the Analyzer) is a full-featured, compact,

ESA620 Users Manual 2 Table 1. Symbols Symbol Description  Risk of Danger. Important information. See Manual.  Hazardous voltage. Risk of electric

Electrical Safety Analyzer Safety Information 3 Safety Information In this manual, a Warning identifies conditions and procedures that are dangero

ESA620 Users Manual 4 • The Analyzer must be properly earthed. Only use a supply socket that has a protective earth contact. If there is any doubt as

Electrical Safety Analyzer Unpacking the Analyzer 5 Unpacking the Analyzer Carefully unpack all items from the box and check that you have the fol

Warranty and Product Support Fluke Biomedical warrants this instrument against defects in materials and workmanship for one year from the date of orig

ESA620 Users Manual 6 Instrument Familiarization Figure 1 and Table 2 describes the top-panel controls and connections of the Analyzer. POLARITYNEUTR

Electrical Safety Analyzer Instrument Familiarization 7 Table 2. Top-Panel Controls and Connections Item Name Description 1 ECG/Applied Parts Pos

ESA620 Users Manual 8 Figure 2 and Table 3 describe the rear-panel connections of the Analyzer. 1243 faw01.eps Figure 2. Rear-Panel Connections

Electrical Safety Analyzer Instrument Familiarization 9 Table 3. Rear-Panel Connections Item Name Description 1 AC Power Switch Turns ac power

ESA620 Users Manual 10 Connecting to Line Power Warning To avoid shock hazard and for proper Analyzer operation, connect the factory supplied three-

Electrical Safety Analyzer Turning the Analyzer On 11 To protective earth or enclosure faw03.eps Figure 4. DUT Connections to the Analyzer

ESA620 Users Manual 12 During the self-test, the Analyzer checks its ac mains input for proper polarity, ground integrity and voltage level. The high

Electrical Safety Analyzer Setting Up the Analyzer 13 faw13.eps Figure 6. Setup Menu The setup parameters have been grouped into six categories:

ESA620 Users Manual 14 To protective earth or enclosure faw12.eps Figure 7. 2-Wire Earth Resistance Measurement Connections

Electrical Safety Analyzer Setting Up the Analyzer 15 To protective earth or enclosureKelvin Test Lead faw11.eps Figure 8. 4-Wire Earth Resistance

Notices All Rights Reserved  Copyright 2008, 2013, Fluke Biomedical. No part of this publication may be reproduced, transmitted, transcribed, stored

ESA620 Users Manual 16 Setting Polarity Switching Delay When switching the polarity of the Analyzer’s test receptacle, a delay can be set to control t

Electrical Safety Analyzer Performing Electrical Safety Tests 17 Performing Electrical Safety Tests The Analyzer is designed to perform a number o

ESA620 Users Manual 18 Performing Mains Voltage Testing The Mains Voltage test measures the voltage on the mains input through three separate measurem

Electrical Safety Analyzer Performing Electrical Safety Tests 19 To perform a protective-earth resistance test: 1. Ensure the power cord from the

ESA620 Users Manual 20 For testing with a >10 A test current: 3. If not already selected, press the softkey labeled High. 4. Press  to apply the

Electrical Safety Analyzer Performing Electrical Safety Tests 21 Table 4. Schematic Abbreviations Abbreviation Meaning MD Measuring Device FE Func

ESA620 Users Manual 22 MDTEST LEADCONDUCTIVE PARTDUT_PEFEDUT_L2DUT_L1DEVICE UNDER TESTAPPLIEDPART faw26.eps Figure 11. Protective-Earth Resistance Mea

Electrical Safety Analyzer Performing Electrical Safety Tests 23 Performing an Insulation Resistance Test The five insulation resistance tests tak

ESA620 Users Manual 24 MDCONDUCTIVE PARTDUT_PEDUT_L2DUT_L1FEDEVICE UNDER TESTAPPLIEDPART faw17.eps Figure 13. Mains to Protective-Earth Insulation Res

Electrical Safety Analyzer Performing Electrical Safety Tests 25 MDCONDUCTIVE PARTDUT_PEDUT_L2DUT_L1FEDEVICE UNDER TESTAPPLIEDPART faw18.eps Figur

Returns and Repairs Return Procedure All items being returned (including all warranty-claim shipments) must be sent freight-prepaid to our factory loc

ESA620 Users Manual 26 MDCONDUCTIVE PARTDUT_PEDUT_L2DUT_L1FEDEVICE UNDER TESTAPPLIEDPART faw19.eps Figure 15. Mains to Applied Parts Insulation Test S

Electrical Safety Analyzer Performing Electrical Safety Tests 27 MDCONDUCTIVE PARTDUT_PEDUT_L2DUT_L1FEDEVICE UNDER TESTAPPLIEDPARTTESTLEAD faw20.e

ESA620 Users Manual 28 MDCONDUCTIVE PARTDUT_PEDUT_L2DUT_L1FEDEVICE UNDER TESTAPPLIEDPARTTESTLEAD faw21.eps Figure 17. Applied Parts to Non-Earth Condu

Electrical Safety Analyzer Performing Electrical Safety Tests 29 Performing a Current Consumption Test To measure the current consumed by the DUT,

ESA620 Users Manual 30 faw16.eps Figure 18. Leakage Current Main Menu Note The display shown in Figure 18 is the main leakage current menu when IEC60

Electrical Safety Analyzer Performing Electrical Safety Tests 31 CONDUCTIVE PARTDUT_PEAPPLIED PARTPEL2DUT_L2DUT_L1MAINSL1L2REVPOLMAINSONMDFEDEVICE

ESA620 Users Manual 32 Performing an Enclosure Leakage Test Note The Enclosure Leakage test is only available for the IEC60601 & ANSI/AMMI ES60601

Electrical Safety Analyzer Performing Electrical Safety Tests 33 CONDUCTIVE PARTDUT_PEAPPLIED PARTTEST LEADPEL2DUT_L2DUT_L1MAINSL1EARTHMAINSONL2MD

ESA620 Users Manual 34 Performing a Patient Leakage Test Note The Patient Leakage Current Test is not available for IEC 62353 or IEC 61010 standard se

Electrical Safety Analyzer Performing Electrical Safety Tests 35 LEADSELECTRELAY*LEAD GNDSELECT RELAY(REMOTE ONLY)CONDUCTIVE PARTDUT_PEPEPEL2DUT_L

Certification This instrument was thoroughly tested and inspected. It was found to meet Fluke Biomedical’s manufacturing specifications when it was sh

ESA620 Users Manual 36 Performing Patient Auxiliary Leakage Tests Note The Patient Auxiliary leakage test is available when the AN/NZS3551, IEC60601,

Electrical Safety Analyzer Performing Electrical Safety Tests 37 + LEADSELECTRELAY*- LEADSELECTRELAY*CONDUCTIVE PARTDUT_PEPEPEL2DUT_L2DUT_L1MAINSL

ESA620 Users Manual 38 The following outlet conditions apply when performing this test: • Normal Polarity • Normal Polarity, Open Neutral • Normal P

Electrical Safety Analyzer Performing Electrical Safety Tests 39 DUT_PEPEL2DUT_L2DUT_L1MAINSL1MAINSOnREVPOLMAPREVMDMAP (ISOLATION)TRANSFORMERFELEA

ESA620 Users Manual 40 Performing an Alternative Equipment Leakage Test Note The alternative equipment leakage test is available when the EN62353 &

Electrical Safety Analyzer Performing Electrical Safety Tests 41 CONDUCTIVE PARTDUT_PEDUT_L2DUT_L1FEDEVICE UNDER TESTAPPLIEDPARTPEOPENTESTLEADMD f

ESA620 Users Manual 42 CONDUCTIVE PARTDUT_PEDUT_L2DUT_L1FEDEVICE UNDER TESTAPPLIEDPARTLEADSELECTRELAY**Leads not selected are open.TESTLEADMD gtv23.

Electrical Safety Analyzer Performing Electrical Safety Tests 43 To perform an alternative applied part leakage test: 1. Press . 2. Press the so

ESA620 Users Manual 44 CONDUCTIVE PARTDUT_PEL2DUT_L2DUT_L1MAINSL1L2MAINSONREVPOLPEPETESTLEADFEDEVICE UNDER TESTAPPLIEDPARTMD faw24.eps Figure 27. Dire

Electrical Safety Analyzer Performing Electrical Safety Tests 45 Performing a Direct Applied Part Leakage Test Note The Direct Applied Part Leakag

ESA620 Users Manual 46 LEADSELECTRELAY**Leads not selected are open.CONDUCTIVE PARTDUT_PEL2DUT_L2DUT_L1MAINSL1L2PEMAINSONREVPOLFEDEVICE UNDER TESTAP

Electrical Safety Analyzer Performing Electrical Safety Tests 47 Performing a Differential Leakage Current Test Note The Differential Leakage Curr

ESA620 Users Manual 48 CONDUCTIVE PARTDUT_PEPEL2DUT_L2DUT_L1MAINSL1EARTHTESTLEADMAINSONREVPOLFEDEVICE UNDER TESTAPPLIEDPARTMD gtv32.eps Figure 29. Dif

Electrical Safety Analyzer Making Point-To-Point Measurements 49 Making Point-To-Point Measurements The Analyzer can make voltage, resistance, and

ESA620 Users Manual 50 Measuring Current The Analyzer can make dc only, ac only, and ac+dc current measurements up to 10 mA. To make a current measure

Electrical Safety Analyzer Simulating ECG Waveforms 51 ECG Monitor faw07.eps Figure 32. ECG Monitor Connections

ESA620 Users Manual 52 Controlling the Analyzer Remotely Fluke Biomedical Ansur test automation software allows a solutions-based approach to complete

Electrical Safety Analyzer Cleaning the Analyzer 53 Cleaning the Analyzer  Warning To avoid electric shock, do not clean the Analyzer plugged in

ESA620 Users Manual 54 Replaceable Parts Table 6 lists the replaceable parts for the Analyzer. Table 6. Replaceable Parts Item Fluke Biomedical Part

Electrical Safety Analyzer Replaceable Parts 55 Table 6. Replaceable Parts (cont.) Item Fluke Biomedical Part Number Null Post Adapter 3326842 C

i Table of Contents Title Page Introduction ...

ESA620 Users Manual 56 Accessories Table 7 lists the available accessories for the Analyzer. Table 7. Accessories Item Fluke Biomedical Part Numb

Electrical Safety Analyzer Specifications 57 Specifications Temperature Operating ... 10

ESA620 Users Manual 58 Detailed Specifications Voltage Mains voltage Ranges ... 0.0 to 300 V

Electrical Safety Analyzer Detailed Specifications 59 Additional error caused by series inductance Resistance Series Inductance 0 µH 100 µH 20

ESA620 Users Manual 60 Crest factor ... ≤3 Ranges ...

Electrical Safety Analyzer Detailed Specifications 61 Insulation resistance Ranges ...

ESA620 Users Manual 62

ESA620 Users Manual ii Performing Electrical Safety Tests ...... 17 Sett

Contents (continued) iii Specifications ..........................